Substantial CZPT and CZPTx Equipment Square 60mm AF Sequence Planetary CZPT for Servo Motor
Solution Description
AF Sequence Planetary CZPT furthermore adds front and rear oil seals, makes use of the output shaft double assistance composition and style of helix gear, which helps make the equipment meshing smoother and secure, the AF Series can be employed in various manage transmission fields with servo motors. The backlash of the AF sequence is significantly less than five arc.min and the reduction ratio addresses 3~one hundred.
The Product Advantages of Planetary CZPT:
one.Adaptable composition style, in line with different functioning situations.
2.Ring gear processing engineering: Making use of inside gear slotting equipment and hobbling equipment the precision of ring equipment soon after processing can reach GB7.
three.Hardened equipment secondary scraping technologies: secondary high-speed dry reducing of gear removes gear deformation induced by heat treatment method. Gear precision can achieve GB6.
4.CZPT backlash screening.
How To Read
60 AF 10 ( ) (S) – 40 T1
a b c d e f g
| a | Frame Dimensions | 60=60mm |
| b | Series code: AF | Square mounting flange collection |
| c | Reduction Ratio | Single Phase: 3,4,five,six,7,8,nine,10 Two Levels: 15,20,twenty five,30,35,40,45,50,sixty,70,80,90,one hundred |
| d | Backlash | One Stage: ≤5arc.min Two Phases: ≤8arc.min |
| e | Input shaft variety | S: Total locking (Omitted) (Regardless of whether the motor has a keyway) S1: Locking with locking ring (Regardless whether the motor has a keyway ) S2: Locking with keyway (Enter shaft with essential) K: With keyway A: Other kinds (Make sure you contact with us) |
| f | Relevant servo motor energy (W),You should get in touch with us for distinct electrical power | |
| g | Please contact us for the mounting type of the flange | |
Spesifications & Particulars
| Solution Variety | Unit | Number Of Phase | Reduction Ratio | 60AF |
| Rated Output Torque | N.M | one | 3 | 34 |
| 4 | 33 | |||
| 5 | 38 | |||
| seven | 36 | |||
| eight | thirty | |||
| ten | 26 | |||
| two | 12 | 48 | ||
| 15 | 48 | |||
| 16 | 47 | |||
| 20 | forty seven | |||
| 25 | 50 | |||
| 32 | 45 | |||
| 35 | forty five | |||
| forty | 43 | |||
| fifty | 50 | |||
| 64 | 37 | |||
| eighty | 32 | |||
| one hundred | 29 | |||
| Max. radial power* | N | 1,two | three~one hundred | 750 |
| Max. axial drive* | 1,2 | 3~one hundred | 375 | |
| Complete Load Performance | % | one | three~10 | ≥97% |
| two | 15~a hundred | ≥94% | ||
| Backlash | arc.min | 1 | 3~ten | ≤5 |
| two | fifteen~a hundred | ≤8 |
*Highest radial force and highest axial pressure, when the output is 100rpm, it acts on the center placement (L/two) of the output shaft.
Dimensions (mm):
| Product type | No. of stage | L1 | L2 | L3 | L4 | L5 | L6 | L7 | L8 | L9 | L10 | D1 | D2 | |
| 60AF | 1 | 116 | 24 | 57 | 35 | 30.five | 25 | 2.five | three | thirty | ten | Φ70 | Φ50G7 | |
| 2 | 126 | 67 | ||||||||||||
| No. of phase | D3 | D4 | D5 | D6 | D7 | D8 | D9 | D10 | B1 | H1 | G1 | G3 | Q3 | |
| 1,two | ≤14G7 | Φ14h7 | Φ20 | Φ50h7 | Φ61 | Φ70 | Φ5.5 | sixty two | 5 | sixteen | M4×10 | M5×15 | sixty |
Particulars of AF sequence Planetary CZPT
System
Compact output shaft mechanism
It adopts the design of output shaft integrated method, compact construction, large rigidity, and it can withstand big influence. Place the enter coupling and the sunlight equipment at the middle of the output shaft to boost the concentricity of the parts, thus effectively managing the gear clearance and strengthening the backlash of the total gearbox.
Structure
Entire needle framework
The inner bearing of the planetary gear adopts a full-needle design and style, the inner hole is manufactured by a grinding procedure, the floor hardness is HRC60, and the cylindricity is less than .003mm.
Other Design Kinds of AF sequence Planetary CZPT
Far more goods,remember to click listed here…
Assembly Procedure
Remember to stick to the ideas bellow to assemble the servo motor and reducer. Besides for specified items, there are various proportions of servo motors, some motors might not be capable to link with flanges.As a result, be certain to use the correct motor which is specified when location your buy.
In Situation Of Assembling A Motor With no Important
1.Take off the rubber cap, switch the enter shaft, and match the head of the bolt to the gap of the rubber cap. Make certain that the correcting bolt is loosened.
two.Slowly place the motor shaft into the enter shaft (Make sure that it is easily place in CZPT jam.). Be cautious not to be inserted with the motor tilted.
three.Connect the motor to the reducer and fasten the bolt with designated fastening torque. See Table one.
four.CZPTen the fixing bolt of the input shaft with specified fastening torque wrench, and so on. See Table two.
five.Set on the rubber cap.
Desk 1
| Motor Mixture Bolt | CZPTening Torque | |
| (N·m) | (kgf·cm) | |
| M3 | 1. | ten |
| M4 | 3. | 30 |
| M5 | five.eight | sixty |
| M6 | 9.8 | 100 |
| M8 | 19.6 | 200 |
| M10 | 39.2 | four hundred |
| M12 | 68.6 | seven-hundred |
| M16 | 168 | 1650 |
Table 2
| Blend Bolt | CZPTening Torque | |
| (N·m) | (kgf·cm) | |
| M3 | 1.5 | 15 |
| M4 | three.five | 35 |
| M5 | 7.1 | seventy one |
| M6 | 12 | one hundred twenty |
| M8 | thirty | three hundred |
| M10 | 60 | 612 |
Firm Profile
Shipping
Our Companies
1.Maintenance time & Warranty: 1 yr right after leaving manufacturing facility
two.Other provider: Which includes modeling variety manual, set up guidebook, and issue capturing information, etc.
FAQ
Q: What’re your main merchandise?
A: We at the moment create Brushed DC Motors, Brushed DC Equipment Motors, Planetary DC Equipment Motors, Brushless DC Motors, AC Motors, High CZPT Planetary CZPT and CZPT Cycloidal CZPT and many others.. You can examine the specs for over motors on our website and you can electronic mail us to advocate required motors for each your specification way too.
Q: How to decide on a suitable motor or gearbox?
A:If you have motor photographs or drawings to demonstrate us, or you have in depth specifications, these kinds of as, voltage, velocity, torque, motor dimension, doing work mode of the motor, necessary life span and sound amount etc, you should do not hesitate to permit us know, then we can advocate appropriate motor for each your request accordingly.
Q: Do you have a CZPT service for your normal motors or gearboxes?
A: Of course, we can customise for each your request for the voltage, pace, torque and shaft measurement/condition. If you need extra wires/cables soldered on the terminal or want to add connectors, or capacitors or EMC we can make it way too.
Q: Do you have an personal style provider for motors?
A: Yes, we would like to design motors separately for our consumers, but some kind of molds are necessory to be developped which may require exact expense and design and style charging.
Q: What’s your guide time?
A: CZPTly talking, our typical common solution will want 15-30days, a little bit longer for CZPT merchandise. But we are really adaptable on the direct time, it will count on the particular orders.
