ZD Higher CZPT and CZPTx Gear Square 60mm AF Sequence Planetary CZPT for Servo Motor
Product Description
AF Series Planetary CZPT furthermore adds entrance and rear oil seals, makes use of the output shaft double support framework and layout of helix gear, which makes the gear meshing smoother and steady, the AF Collection can be utilised in various management transmission fields with servo motors. The backlash of the AF collection is significantly less than five arc.min and the reduction ratio covers 3~a hundred.
The Product Advantages of Planetary CZPT:
one.Flexible composition design, in line with different operating conditions.
2.Ring equipment processing technology: Employing inside gear slotting equipment and hobbling equipment the precision of ring gear after processing can get to GB7.
three.Hardened equipment secondary scraping technologies: secondary high-speed dry reducing of gear gets rid of equipment deformation induced by warmth therapy. Equipment precision can attain GB6.
four.CZPT backlash tests.
How To Read through
60 AF 10 ( ) (S) – 40 T1
a b c d e f g
| a | Frame Measurement | sixty=60mm |
| b | Series code: AF | Sq. mounting flange collection |
| c | Reduction Ratio | One Phase: 3,four,five,six,seven,eight,nine,ten Two Levels: fifteen,twenty,25,thirty,35,forty,45,fifty,sixty,70,80,ninety,one hundred |
| d | Backlash | Single Phase: ≤5arc.min Two Stages: ≤8arc.min |
| e | Input shaft sort | S: All round locking (Omitted) (Irrespective of whether or not the motor has a keyway) S1: Locking with locking ring (Regardless no matter whether the motor has a keyway ) S2: Locking with keyway (Enter shaft with essential) K: With keyway A: Other kinds (Please get in touch with with us) |
| f | Relevant servo motor electrical power (W),You should make contact with us for specific power | |
| g | Remember to get in touch with us for the mounting kind of the flange | |
Spesifications & Specifics
| Merchandise Sort | Device | Number Of Stage | Reduction Ratio | 60AF |
| Rated Output Torque | N.M | one | three | 34 |
| four | 33 | |||
| 5 | 38 | |||
| seven | 36 | |||
| 8 | 30 | |||
| ten | 26 | |||
| two | twelve | forty eight | ||
| fifteen | 48 | |||
| 16 | 47 | |||
| twenty | 47 | |||
| 25 | 50 | |||
| 32 | 45 | |||
| 35 | forty five | |||
| 40 | 43 | |||
| fifty | 50 | |||
| 64 | 37 | |||
| 80 | 32 | |||
| 100 | 29 | |||
| Max. radial drive* | N | 1,two | 3~100 | 750 |
| Max. axial pressure* | one,two | 3~100 | 375 | |
| Total Load Effectiveness | % | one | three~10 | ≥97% |
| two | 15~a hundred | ≥94% | ||
| Backlash | arc.min | 1 | three~ten | ≤5 |
| 2 | 15~one hundred | ≤8 |
*Highest radial drive and greatest axial force, when the output is 100rpm, it acts on the center situation (L/two) of the output shaft.
Dimensions (mm):
| Product kind | No. of stage | L1 | L2 | L3 | L4 | L5 | L6 | L7 | L8 | L9 | L10 | D1 | D2 | |
| 60AF | 1 | 116 | 24 | fifty seven | 35 | thirty.5 | 25 | 2.five | 3 | 30 | ten | Φ70 | Φ50G7 | |
| two | 126 | 67 | ||||||||||||
| No. of stage | D3 | D4 | D5 | D6 | D7 | D8 | D9 | D10 | B1 | H1 | G1 | G3 | Q3 | |
| 1,two | ≤14G7 | Φ14h7 | Φ20 | Φ50h7 | Φ61 | Φ70 | Φ5.5 | 62 | 5 | sixteen | M4×10 | M5×15 | sixty |
Details of AF collection Planetary CZPT
Mechanism
Compact output shaft mechanism
It adopts the layout of output shaft built-in system, compact composition, large rigidity, and it can face up to big impact. Place the input coupling and the sunshine gear at the centre of the output shaft to increase the concentricity of the factors, therefore effectively managing the gear clearance and enhancing the backlash of the entire gearbox.
Construction
Complete needle structure
The internal bearing of the planetary equipment adopts a full-needle layout, the inner gap is made by a grinding approach, the surface hardness is HRC60, and the cylindricity is less than .003mm.
Other Product Sorts of AF sequence Planetary CZPT
More items,you should click listed here…
Assembly Method
Please stick to the ideas bellow to assemble the servo motor and reducer. Except for specified goods, there are various dimensions of servo motors, some motors might not be in a position to link with flanges.For that reason, be positive to use the suitable motor which is specified when place your buy.
In Case Of Assembling A Motor With out Crucial
1.Get off the rubber cap, switch the input shaft, and match the head of the bolt to the hole of the rubber cap. Make confident that the repairing bolt is loosened.
two.Gradually put the motor shaft into the enter shaft (Make sure that it is efficiently put in CZPT jam.). Be cautious not to be inserted with the motor tilted.
3.Attach the motor to the reducer and fasten the bolt with designated fastening torque. See Table one.
4.CZPTen the repairing bolt of the enter shaft with selected fastening torque wrench, and so forth. See Desk 2.
5.Place on the rubber cap.
Table 1
| Motor Mixture Bolt | CZPTening Torque | |
| (N·m) | (kgf·cm) | |
| M3 | 1. | 10 |
| M4 | three. | 30 |
| M5 | five.8 | sixty |
| M6 | nine.eight | 100 |
| M8 | 19.six | two hundred |
| M10 | 39.2 | four hundred |
| M12 | sixty eight.six | 700 |
| M16 | 168 | 1650 |
Table 2
| Blend Bolt | CZPTening Torque | |
| (N·m) | (kgf·cm) | |
| M3 | one.5 | 15 |
| M4 | 3.five | 35 |
| M5 | 7.1 | 71 |
| M6 | twelve | a hundred and twenty |
| M8 | thirty | 300 |
| M10 | sixty | 612 |
Organization Profile
Shipping
Our Solutions
one.Upkeep time & Warranty: 1 yr right after leaving manufacturing facility
two.Other support: Including modeling variety manual, set up information, and dilemma taking pictures manual, etc.
FAQ
Q: What’re your primary products?
A: We currently produce Brushed DC Motors, Brushed DC Gear Motors, Planetary DC Equipment Motors, Brushless DC Motors, AC Motors, Substantial CZPT Planetary CZPT and CZPT Cycloidal CZPT and so forth.. You can examine the requirements for earlier mentioned motors on our internet site and you can e-mail us to advise necessary motors for each your specification too.
Q: How to pick a appropriate motor or gearbox?
A:If you have motor images or drawings to present us, or you have detailed specifications, this sort of as, voltage, pace, torque, motor size, functioning method of the motor, necessary life time and noise degree and so on, please do not hesitate to let us know, then we can recommend suited motor per your request appropriately.
Q: Do you have a CZPT service for your standard motors or gearboxes?
A: Indeed, we can customise for every your request for the voltage, velocity, torque and shaft measurement/form. If you need to have added wires/cables soldered on the terminal or need to insert connectors, or capacitors or EMC we can make it as well.
Q: Do you have an personal style support for motors?
A: Yes, we would like to style motors separately for our customers, but some sort of molds are necessory to be developped which may need to have actual value and layout charging.
Q: What’s your guide time?
A: CZPTly speaking, our normal normal merchandise will need fifteen-30days, a bit more time for CZPT products. But we are quite adaptable on the lead time, it will rely on the certain orders.
