ZD IP65 Protection Quality High CZPT and CZPTx Gear Spherical 90mm AE Collection Planetary CZPT
AE Series Planetary CZPT additionally adds entrance and rear oil seals, employs the output shaft double assist composition and layout of helix gear, which tends to make the gear meshing smoother and stable, the AE Series can be utilized in a variety of manage transmission fields with servo motors. The backlash of the AE collection is less than 5 arc.min and the reduction ratio handles 3~100.
The Product Advantages of Planetary CZPT:
one.Versatile framework design, in line with various operating situations.
two.Ring equipment processing technologies: Employing internal equipment slotting device and hobbling device the precision of ring equipment after processing can reach GB7.
three.Hardened equipment secondary scraping engineering: secondary large-velocity dry chopping of equipment eliminates gear deformation caused by heat treatment. Gear precision can reach GB6.
4.CZPT backlash screening.
How To Read
90 AE 10 ( ) (S) – 40 T1
a b c d e f g
|b||Series code: AE||Spherical mounting flange series|
|c||Reduction Ratio|| Single Phase: 3,4,5,six,7,8,9,ten
Two Stages: 15,20,twenty five,30,35,forty,45,fifty,sixty,70,80,ninety,100
|d||Backlash|| Single Phase: ≤5arc.min
Two Phases: ≤8arc.min
|e||Input shaft kind|| S: General locking (Omitted) (Regardless of whether or not the motor has a keyway)
S1: Locking with locking ring (No matter no matter whether the motor has a keyway )
S2: Locking with keyway (Enter shaft with important)
K: With keyway
A: Other types (Please make contact with with us)
|f||Applicable servo motor power (W),Please make contact with us for certain energy|
|g||Please contact us for the mounting kind of the flange|
Spesifications & Particulars
|Product Variety||Unit||Number Of Phase||Reduction Ratio||90AE|
|Rated Output Torque||N.M||one||three||85|
|5||one hundred and five|
|2||12||one hundred fifteen|
|16||a hundred thirty|
|20||one hundred thirty|
|twenty five||a hundred thirty five|
|32||one hundred twenty|
|35||one hundred twenty five|
|forty||a hundred and fifteen|
|50||one hundred thirty five|
|Max. radial drive*||N||1,2||three~one hundred||2100|
|Max. axial drive*||one,two||3~100||1050|
|Total Load Performance||%||one||three~10||≥97%|
*Greatest radial pressure and optimum axial pressure, when the output is 100rpm, it acts on the center position (L/two) of the output shaft.
|Merchandise type||No. of stage||L1||L2||L3||L4||L5||L6||L7||L8||L9||L10||D1||D2|
|No. of phase||D3||D4||D5||D6||D7||D8||B1||H1||G1||G2||G3||Q3|
Particulars of AE sequence Planetary CZPT
Compact output shaft mechanism
It adopts the style of output shaft built-in system, compact construction, high rigidity, and it can withstand huge influence. Spot the input coupling and the sunlight equipment at the center of the output shaft to improve the concentricity of the parts, thus successfully controlling the equipment clearance and improving the backlash of the total gearbox.
Complete needle construction
The interior bearing of the planetary equipment adopts a full-needle design and style, the internal gap is manufactured by a grinding approach, the floor hardness is HRC60, and the cylindricity is less than .003mm.
When compared with AF Sequence
AF sequence planetary gearbox uses square by means of hole flange, but AE sequence employs spherical threaded flange.
For other requirements, AE series planetary gearbox is related with AF collection.
Other Design Sorts of AE sequence Planetary CZPT
Far more merchandise,you should simply click below…
Please stick to the ideas bellow to assemble the servo motor and reducer. Besides for specified merchandise, there are various proportions of servo motors, some motors might not be able to hook up with flanges.Therefore, be sure to use the correct motor which is specified when place your purchase.
In Case Of Assembling A Motor Without having Key
one.Just take off the rubber cap, change the enter shaft, and match the head of the bolt to the gap of the rubber cap. Make sure that the correcting bolt is loosened.
two.Steadily set the motor shaft into the enter shaft (Ensure that it is smoothly put in CZPT jam.). Be watchful not to be inserted with the motor tilted.
3.Connect the motor to the reducer and fasten the bolt with selected fastening torque. See Desk 1.
four.CZPTen the correcting bolt of the enter shaft with designated fastening torque wrench, and many others. See Table 2.
5.Set on the rubber cap.
|Motor Mixture Bolt||CZPTening Torque|
|Mix Bolt||CZPTening Torque|
|M6||twelve||a hundred and twenty|
Shipping and delivery
1.Upkeep time & Warranty: one 12 months soon after leaving factory
2.Other support: Which includes modeling choice guide, set up manual, and dilemma capturing manual, etc.
Q: What’re your main merchandise?
A: We at present make Brushed DC Motors, Brushed DC Gear Motors, Planetary DC Equipment Motors, Brushless DC Motors, AC Motors, Substantial CZPT Planetary CZPT and CZPT Cycloidal CZPT etc.. You can verify the technical specs for previously mentioned motors on our site and you can e-mail us to advise necessary motors for every your specification way too.
Q: How to select a ideal motor or gearbox?
A:If you have motor photographs or drawings to display us, or you have thorough requirements, such as, voltage, speed, torque, motor dimension, operating mode of the motor, necessary lifetime and sounds degree etc, please do not hesitate to let us know, then we can advise suitable motor per your ask for appropriately.
Q: Do you have a CZPT services for your normal motors or gearboxes?
A: Of course, we can customize per your ask for for the voltage, speed, torque and shaft dimension/form. If you require added wires/cables soldered on the terminal or need to have to incorporate connectors, or capacitors or EMC we can make it also.
Q: Do you have an individual design and style service for motors?
A: Yes, we would like to design and style motors independently for our clients, but some sort of molds are necessory to be developped which could want precise cost and layout charging.
Q: What is actually your direct time?
A: CZPTly talking, our normal common merchandise will need to have 15-30days, a bit lengthier for CZPT goods. But we are really versatile on the guide time, it will rely on the distinct orders.